Views: 0 Author: Site Editor Publish Time: 2026-10-19 Origin: Site
When a molded plastic part shows a defect, it is tempting to focus only on the machine settings. In practice, the root cause may begin earlier in the part design, material selection or mold layout.
A strong prevention strategy connects the defect to the entire process. Wall thickness, gate position, cooling, ejection, material behavior and inspection criteria should be reviewed before the mold is released for production.
Sink marks often appear when a thicker section cools and shrinks more than the surrounding wall. Ribs, bosses and heavy intersections can create this condition, especially when the thicker feature sits behind a visible surface.
Design can reduce the risk by keeping wall transitions balanced and using well-proportioned ribs or bosses. Mold cooling and process conditions also influence the final appearance.
If a sink mark is found, the team should identify its exact location and relationship to internal geometry. A visual change alone may not solve the underlying cause if the design still contains an unbalanced section.
Warpage occurs when different areas of a part shrink or cool at different rates. Large flat surfaces, uneven wall thickness, long flow paths and asymmetric geometry can all contribute to distortion.
A DFM review can identify high-risk areas before tooling. Gate position, cooling layout, material behavior and ejection support should be considered together. For an assembly part, the most important question is not only whether the part is flat, but whether it still fits and functions correctly.
Flash is excess plastic that appears along the parting line or around inserts. It may be related to parting-line condition, mold alignment, wear, process pressure or other production factors.
The location and pattern of flash provide useful evidence. A consistent flash line may point to a tooling or parting issue, while a change that appears only in certain production conditions may require a process review.
Regular mold maintenance and clear inspection limits are important for repeat production.
Weld lines can form where two flow fronts meet. Their appearance and strength depend on the material, geometry, gate location, temperature and flow behavior.
A weld line is not automatically a failure. Its location matters. A line on a hidden internal area may be acceptable, while the same line across a visible or functional feature may require a design or tooling change.
The buyer should identify appearance-critical areas and strength-sensitive features early so the supplier can include them in the mold review.
A short shot occurs when the cavity is not fully filled. Thin walls, long flow paths, insufficient venting or unsuitable process conditions may contribute. Burn marks can be associated with trapped air and excessive local heat.
These issues should be investigated using the actual part geometry and mold layout rather than solved through assumptions. A small design change, improved venting or different gate location may be more effective than simply increasing process pressure.
Ejector marks can appear when the part requires excessive force to release or when the ejection system applies pressure to a visible area. Draft, texture, cooling and ejection balance all influence the result.
Surface defects may also be related to material moisture, contamination, color dispersion or inconsistent processing. A defined visual standard helps the team distinguish an acceptable process mark from a defect that affects the product.
When a defect is reported, record:
Part number and drawing revision.
Production batch or sample version.
Defect location and quantity affected.
Photos under consistent lighting.
Measurement or assembly impact.
Whether the defect is cosmetic, functional or both.
The proposed corrective action and verification method.
This evidence-based approach makes it easier to separate design, tooling, material, process and handling causes.
Jingwei supports custom plastic parts for electronics, medical equipment and industrial applications. A project-specific DFM and quality review can help identify risk areas before production and establish inspection criteria for critical features.
No general checklist can replace a review of the actual part. The most useful prevention work starts with the drawing, material, application and production requirements.
There is no single defect that appears in every project. Sink marks, warpage, flash, weld lines, short shots and surface marks can all occur depending on the design, material, mold and process.
Sometimes, but not always. The root cause may be related to wall thickness, gate design, cooling, venting, material or ejection. The full molding system should be reviewed before changing settings alone.
Begin with balanced wall thickness and a DFM review. Gate placement, cooling, material behavior, ejection and the part’s assembly requirements should also be considered.
Not necessarily. Acceptability depends on location, appearance standard, structural effect and product function. The buyer and supplier should agree on the standard before production approval.
Share your part drawing and defect photos for a structured discussion of possible design, tooling and process factors.
Learn how insert molding combines metal and plastic in one component, with practical guidance on insert selection, mold design, assembly and quality control.
Understand the practical path from plastic part prototype to production, including DFM, tooling, mold trials, sample approval and repeat manufacturing.
Compare practical surface finish considerations for injection molded plastic parts, including gloss, texture, polishing, marks, color and draft.
Learn how to design injection molded snap-fit plastic parts with practical attention to flexibility, draft, stress, clearance, tooling and assembly.